Package Contents

Installation Requirements

• 7 mm socket wrench or screwdriver
• Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.

  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable

Application Examples

The LiteBeam ac mounted outdoors with the reflector installed provides directional outdoor coverage (gain reflector-dependent).

The LiteBeam ac mounted outdoors without the reflector installed provides outdoor-to-indoor coverage using the 3 dBi Antenna Feed only.

Hardware Overview

Ethernet LED
The LED will light steady blue when an active Ethernet connection is made and flash when there is activity.
Power LED
The LED will light blue when the device is connected to a power source.
Reset Button
To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.
Ethernet Port
This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.

Hardware Installation

The LiteBeam was designed for outdoor use and quick mounting on a pole. You may mount it on a wall using an optional Wall Mount Kit, model NBE-WMK (sold separately).

1. 

2. 

3. 

4.  





Optional (M3x4 self-tapping screws not included)



5. 

6. 

7. 

8. 

Pole Mounting

1. 

2. 

3. 

Wall Mounting

The LiteBeam must be mounted directly to a wood stud or other structurally stable surface using the Wall Mount Kit, model NBE-WMK (sold separately).

	Note: Center screw included. Two optional screws (not included) may provide additional stability.

1. 

2. 

Aiming

1. 

2. 

3. 

4. 

5. 

6. 

Connecting Power

	WARNING: The switch port must comply with the power specifications listed in the “Specifications”.

OR

Accessing airOS

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.

Antenna

Select your antenna from the list. If Calculate EIRP Limit is enabled, transmit output power is automatically adjusted to comply with the regulations of the applicable country. For a Custom antenna, Antenna Gain is entered manually. Note the requirements and antenna types listed below.

Cable Loss (When applicable)

Enter the cable loss in dB. Output power is adjusted to compensate for loss between the radio and the antenna.

Certified Antenna Types

This radio transmitter FCC ID: SWX-LBE5AC / IC: LBE5AC has been approved by FCC / ISED Canada to operate with the antenna types listed below with the maximum permissible gain for each antenna type indicated. Antenna types not included in this list or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna	Frequency	Gain
Grid	5 GHz	23 dBi

Specifications

LBE-5AC-23
Dimensions	358 x 272 x 222 mm (14.09 x 10.71 x 8.74")
Weight	0.75 kg (1.65 lb)
Networking Interface	(1) 10/100/1000 Ethernet Port
Antenna Gain	23 dBi
Max. Power Consumption	7W
Power Supply	24V, 0.3A Gigabit PoE Adapter (Included)
Power Method	Passive PoE (Pairs 4, 5+; 7, 8-)
Operating Temperature	-40 to 70° C (-40 to 158° F)
Operating Humidity	5 to 95% Noncondensing
ESD/EMP Protection	± 24 kV Contact / Air
Shock and Vibrations	ETSI300-019-1.4
Certifications	CE, FCC, IC
Wind Survivability	200 km/h (125 mph)
Wind Loading	283 N @ 200 km/h (63.6 lbf @ 125 mph)

LBE-5AC-23 Operating Frequency (MHz)
Worldwide	5150 - 5875
USA	U-NII-1	5150 - 5250
	U-NII-2A	5250 - 5350
	U-NII-2C	5470 - 5725
	U-NII-3	5725 - 5850